HomeSolarBattery backupSolar + batterySolar + battery + generatorAdd-on: EV chargersAdd-on: Permanent lightingProjectsCalculatorBook a ConsultAbout(780) 200-5265Book a free roof check →
A home in deep snow with solar panels on the roof and an EP Cube 2.0 battery on the outside wall, lights and fireplace on inside
Whole-home battery backup · Edmonton & Alberta

Whole-home battery backup, built for Alberta.

When the grid goes down, the battery takes over in milliseconds and the house keeps running.

The Canadian Solar EP Cube 2.0: 5 to 40 kWh, up to 11.5 kW continuous, 10-year warranty. Installed across Edmonton and Alberta by our own Red Seal–supervised crew, at one written price from a free assessment.

5.0★ on Google550+ Alberta installsRed Seal Master Electrician–led(780) 200-5265
EP Cube 2.0 · by Canadian Solar
0kW
Continuous Output
15–40 kWh sizes
0kWh
Max Capacity
5 kWh steps, two units
Seamless
Auto Switchover
no flicker, no reset clocks
0yr
Warranty
6,000 cycles · LiFePO4

What we install

Built for an Alberta winter.

Three pieces of hardware, one system. The battery and its inverter are the Elite package; the generator makes it Ultimate.

Swipe for all three →

EP Cube 2.0 battery

1 · Battery backup, optional

EP Cube 2.0, 5 to 40 kWh

Slim towers on the garage wall. By day they soak up your surplus. By night they run the house, so you buy almost nothing from the grid. When the grid fails, they take over before a light can flicker.

Warranty10 years
Output at onceUp to 11.5 kW per tower
Switch-overUnder a second
ExpandableUp to 40 kWh
EP Cube hybrid inverter

2 · Hybrid inverter, battery packages

EP Cube hybrid inverter, 11.5 kW

When you add a battery, one hybrid inverter runs the panels and the battery together. It decides, every second, whether the roof’s power goes to the house, into the battery, or to the grid, and it is what switches the house over in an outage.

Warranty10 years
Output11.5 kW continuous · 23 kW with a second unit
Switch-overUnder a second
Used inAny package with a battery
Inside a Generac Guardian standby generator: the engine, its starter battery and the controls

3 · Standby generator, Ultimate package

Generac 18 kW, on natural gas

For the outage that lasts days, not hours. When the battery runs low the generator starts itself, runs the house and recharges the battery, then shuts off. It runs on your natural gas line, so there is no fuel to haul. The battery still does the instant switch-over, so the lights stay on while the generator starts.

Warranty5 years, Generac
OutputGuardian 18 kW · 17 kW on natural gas
PlacementNext to your gas meter
IncludesPad, gas and electrical connections, permits, cold-weather kit
An EP Cube 2.0 battery and inverter on the brick wall of a home with rooftop solar

The quiet machine in your garage.

EP Cube 2 home battery storage system, wall-mounted inverter and battery stack
11.5 kWcontinuous output on the 15–40 kWh sizes — Powerwall 3–class power, with 185 A of motor-start surge
5 kWh stepsmodular, stackable capacity — expand any unit later, up to the 40 kWh Alberta residential cap
Wall-mountNEMA 4X enclosure; the attached garage is the standard Alberta install location
In-houseinstalled, permitted and inspected by our own electricians — never subcontractors

Authorized Canadian Solar / EP Cube dealer

Every spec — checked against the official EP Cube 2.0 datasheet
Canadian Solar EP Cube wall-mounted home battery and inverter on exterior wall
The full system: wall-mounted hybrid inverter and stacked battery modules.
LiFePO4
Battery Chemistry

Most stable lithium chemistry — far higher thermal-runaway threshold than NMC. Tested to UL 9540A.

NEMA 4X
Enclosure Rating

Waterproof and dustproof. Operates from -10°C to 50°C. Indoor or outdoor.

Modular
Stackable Design

5 kWh modules (EP Cube 2.0). Expand capacity anytime. Up to two units in parallel — 40 kWh residential cap per CEC Rule 64-918.

Battery (EP Cube 2.0)

Capacity: 5–40 kWh per unit, in 5 kWh steps
Chemistry: LiFePO4 (Lithium Iron Phosphate)
Module size: 5 kWh per module
Warranty: 10 years / 6,000 cycles (≥80% retained capacity)

Inverter (built-in)

Continuous output: 11.5 kW (15–40 kWh); 8.0 kW (10 kWh); 3.0 kW (5 kWh)
Motor start: 185 A LRA (15–40 kWh)
Switchover: seamless via Smart Gateway
PV input: 6 MPPTs — no separate solar inverter needed
CEC efficiency: 96.5%
Warranty: 10 years

Installation

Location: attached or detached garage (most common), or a dedicated in-home battery room — 18-in side clearances, fire-rated door, fire alarm, exhaust fan
Mounting: Wall-mounted
Permitting: Included
Inspection: City inspection included
Installation warranty: 5 years on Essential (10 years on Premium)

EP Cube comes with a 10-year warranty — see all coverage →  ·  Official EP Cube 2.0 datasheet (PDF, V1.2 — every spec on this page checked against it) →

Winter-proof by design

Cold snaps are when backup earns its keep.

Cold snaps are when the grid gets tested — and when backup earns its keep. Your EP Cube lives in the garage or a dedicated battery room, inside the home’s warm envelope, while its −40°C-rated Smart Gateway stands watch on the grid outside. Furnace fan, sump pump, fridge, Wi-Fi — carried through the cold, automatically.

Find your battery size →

Choose your package

Same panels. Same crew. Four levels of promise.

Every package is the same LONGi panels and the same crew. Prices are per home, so the cards carry none: your written design shows each package’s price for your roof.

Swipe to compare the four packages →

LONGi panels with wire-mesh rodent guard on an Edmonton roof
Essentials

The system, done properly.

  • Your designed solar systemPanels, micro-inverters and engineered mounting
  • Structural review, permits, utility coordination and installation
  • Wire-mesh critter guard & production monitoring
  • 5-year workmanship coverage
  • 5-year roof-leak coverage for our workmanship

For the homeowner focused on producing electricity and cutting grid purchases.

See this on my roof
Black solar panels finished with SolaTrim around the edges, on a Premium install in Edmonton
Premium · most chosen

The promise that never expires.

  • Everything in Essentials, upgraded:SolaTrim replaces the wire-mesh guard
  • SolaTrim perimeter finishA rigid, finished edge that helps keep pests out
  • 10-year workmanship coverage
  • Life-of-roof leak promiseFor leaks caused by our workmanship, subject to written terms
  • Whole-home energy visibilitySee consumption alongside production
  • Future expansion planningSubject to roof and electrical capacity

For the homeowner who wants the install looked after for the life of the roof.

See this on my roof
EP Cube 2.0 battery and its inverter on the outside wall of a home
Elite · add a battery

Self-sufficient, most of the time.

  • EP Cube 2.0 battery backupStores the afternoon for the evening; carries the house in an outage
  • EP Cube hybrid inverter, 11.5 kWReplaces the micro-inverters, runs panels and battery together
  • 10-year battery warranty
  • Everything in the package you build it onEssentials or Premium; an optional second inverter for 23 kW at once

For the home that should run on its own power most of the time, and keep running when the grid stops.

See this on my roof
Generac Guardian standby generator with its automatic transfer switch
Ultimate · battery + generator

Power, no matter what.

  • Everything in EliteBattery, hybrid inverter, 10-year battery warranty
  • Generac 18 kW standby generatorNatural gas. Starts itself when the battery runs low, recharges it, keeps the whole house running for days
  • Pad, gas and electrical connections, permitsInstalled next to your gas meter · 5-year Generac warranty

For the home that has to stay on for as long as the outage lasts.

See this on my roof

Premium isn’t a better install, it’s a longer promise: same panels, same crew, same standard. If a mount ever leaks, it stays ours to fix for the life of the roof. Elite adds a battery to either one, so the house runs on its own power most of the time and keeps running when the grid stops. Ultimate adds a standby generator, so it keeps running for as long as the outage lasts.

Compare the four packages in one table
PackageIn one lineIncludes
EssentialsThe system, done properly.Designed system, structural review, permits, installation, wire-mesh critter guard, monitoring, 5-year workmanship and roof-leak coverage
PremiumThe promise that never expires.Essentials + SolaTrim finish, 10-year workmanship, life-of-roof leak promise, whole-home visibility, expansion planning
EliteSelf-sufficient, most of the time.Premium + EP Cube 2.0 battery, EP Cube hybrid inverter, 10-year battery warranty, optional second inverter
UltimatePower, no matter what.Elite + Generac 18 kW standby generator with pad, gas and electrical connections, and permits

What each package shows you

You will always know what your roof is doing.

The APsystems app is included with every package. Premium and Elite add consumption monitoring, so you also see what the house uses and what goes to the grid.

EssentialsProduction monitoring, every panel.
Live power today
Today, livePower right now, energy so far, peak for the day.
Panel by panel output
Panel by panelEach panel reports its own watts. A weak one shows up at once.
Daily history
Day, month, yearHistory and totals, any time.
Premium & EliteFull energy visibility: roof, house and grid.
Solar, house load and grid, live
Roof, house, gridWhat the roof makes, what the house uses, what crosses the meter, live.
Production through the day
Through the dayProduction curve and peak, every day.
Produced, consumed, imported, exported
Sold and boughtProduced, consumed, imported and exported, by day and month. Your bill, explained before it arrives.
Elite & UltimatePlus the EP Cube app for the battery.
EP Cube app showing charge level, on a phone
The EP Cube appCharge level and what the battery is doing, live.
EP Cube app reserve setting, on a phone
Your reserve, your callChoose how much to keep back for an outage.
EP Cube app history screen, on a phone
HistoryWhere every kilowatt-hour went: house, battery, grid.
The same thing as a table: monitoring by package
PackageWhat you see
EssentialsProduction monitoring on every panel, in the APsystems EMA app, for the life of the system.
PremiumProduction and consumption: what the house uses beside what the roof makes, and what crosses the meter.
ElitePremium, plus the EP Cube app: charge level, solar in, home draw, your outage reserve and history.
UltimateElite, plus the generator’s work in the battery’s charge level: it starts when the battery runs low and stops when it is full.
Stellar Upgrades Red Seal electrician installing an EP Cube 1.0 19.9 kWh battery backup, integrated with an existing rooftop solar system and a Generac standby generator, at a Sherwood Park, Alberta home
Customer Story · Real Stellar install, Sherwood Park

Our solar was installed four years ago by a different company. When we asked them about adding battery backup, they said they couldn’t figure out the integration. Stellar got it done. The EP Cube ties into our existing solar and our Generac standby, and the system manages itself, solar by day, battery at night, generator as final backup. We don’t worry about outages anymore.

19.9 kWh whole-home backupSolar + Battery + Generac, fully integrated
MerlinSherwood Park · Verified Stellar Upgrades battery customer
Get my battery backup assessment →
Elite and Ultimate, in one home

One system. Four situations. Always on.

Merlin’s Sherwood Park system: solar, EP Cube battery, grid and Generac, fully automatic. Tap a card.

Currently showing Daytime
Interactive energy flow diagram of Merlin’s integrated EP Cube battery backup system Diagram showing how Merlin’s EP Cube 1.0 19.9 kWh battery integrates with his existing rooftop solar, his grid connection, his Generac standby generator, and his home. Four operating modes cycle automatically and can be selected by tapping each mode card: daytime solar charging, nighttime battery discharge, cloudy or snow-covered solar with grid top-up, and power outage with under-20-millisecond switchover and automatic Generac start at 10 percent battery. Solar Array Rooftop PV Offline · anti-islanding Grid EPCOR / Fortis Disconnected EP Cube 1.0 19.9 kWh Generac Standby Generator Home Critical Loads
The Moment It Matters

The grid fails. Nothing blinks.

Grid drops, battery takes over. Grid returns, it hands back. You do nothing.

A modern home in a rainstorm with its lights on, rooftop solar, and an EP Cube 2.0 battery on the wall beside the window
Animated demonstration · not a recording
2:59 AM. A winter storm rolls in.
Without battery ⚠ Blackout — sump pump dead EP With EP Cube 2.0 ✓ Seamless — nothing blinked
1 · Grid fails2 · EP Cube takes over3 · Life goes on

Switchover spec per the official EP Cube 2.0 datasheet: seamless. See it live at your free assessment.

Why Battery Backup

One bad outage costs more than the battery.

$5,000–$15,000Frozen, burst pipes when the furnace fan stops
$3,000–$10,000Basement flood when the sump pump dies
$300–$800Fridge and freezer spoiling within four hours
Hours → daysAlberta outages from storms, cold snaps and grid alerts

Ranges drawn from Insurance Bureau of Canada water-damage averages and Alberta property-claim data, as compiled in our 2026 cost breakdown.

Find Your Battery

What size does your home need?

Four taps. We’ll size it.

Step 1 of 4

How big is your home?

This helps us estimate your electrical load.

What must stay powered during an outage?

Select all that apply. More loads = larger battery.

How long should your backup last?

Think about the longest outage you'd want to ride through.

Do you have solar panels?

If yes, your battery can recharge from the sun during outages.

Your Recommended Battery
20 kWh
EP Cube — Full Day Backup
Estimated ~13 hours of backup for your selected loads.

What's included in every installation:

EP Cube battery system
Built-in hybrid inverter (up to 11.5 kW)
Master Electrician installation
Engineering & system design
All permits & utility paperwork
City inspection & activation
10-year battery warranty
Up to 10-year installation warranty
Lifetime app monitoring
$0-down financing available

Get your exact quote — free, no obligation.

We'll confirm the right size, assess your electrical panel, and give you the exact all-in price for your home.

By submitting, you consent to Stellar Upgrades contacting you by phone, text or email about your inquiry. Unsubscribe anytime. Privacy Policy

No spam. A Stellar team member calls within 24 hours.

Interactive Backup Designer

Design your backup. To the hour.

Tap what stays on. Pick a size. See exactly how long you last.

Average draw
0 W
If everything ran at once
0.0 kW
Power ceiling check11.5 kW max output
Select loads to begin.
EP Cube 2.0 size (per unit)
--hrs
select what stays on
Or tell us how long you want to last
Price this exact design — free, in writing.
Your 15 kWh design goes straight to our team with your loads and runtime.

Written all-in quote · a real person calls within 24 h · no spam, ever. 550+ Alberta installs · BBB A+

✓ Design received.

We’ll call within 24 hours with your written all-in price. In a hurry? (780) 200-5265

Your runtime at every size — tap a bar to switch

Assumptions: typical Alberta appliance wattages with winter/summer duty cycles; 90% usable capacity (≈95% LFP depth of discharge × ≈95% conversion efficiency). Runtimes are estimates — final sizing is verified at your free site assessment. Need more than 20 kWh? Two units pair to the 40 kWh Alberta residential cap (CEC Rule 64-918) in dual-tower configurations.

Typical result: a winter “essentials” load in an Alberta home — fridge, deep freezer, furnace fan, sump pump, 10 LED lights, Wi-Fi, phones, and security cameras — averages roughly 530 W. At 90% usable capacity that runs approximately 8 hours on a 5 kWh EP Cube 2.0, 17 hours on a 10 kWh, 25 hours on a 15 kWh, and 34 hours on a 20 kWh. Pairing the battery with solar panels recharges it each day, extending backup through multi-day outages.

Runtime Guide

How long each size runs your home.

Worst-case math — every load running non-stop. Real homes do better; the Designer models that.

EP Cube 2.0 — 5–20 kWh per unit, in stock now

ApplianceDraw5 kWh10 kWh15 kWh20 kWh
Continuous output—3.0 kW8.0 kW11.5 kW11.5 kW
Fridge + Freezer150W~30 hrs~60 hrs~90 hrs~120 hrs
Furnace Fan500W~9 hrs~18 hrs~27 hrs~36 hrs
LED Lights (10)100W~45 hrs~90 hrs~135 hrs~180 hrs
Sump Pump800W~6 hrs~11 hrs~17 hrs~22 hrs
Essential Bundle*~1 kW~4.5 hrs~9 hrs~13 hrs~18 hrs
EP Cube 1.0 owner? Reference runtime tables (7.6 kW continuous, all sizes)

EP Cube 1.0 — sold out at the supplier; every installed unit fully supported

ApplianceDraw9.9 kWh13.3 kWh16.6 kWh19.9 kWh
Fridge + Freezer150W~59 hrs~80 hrs~100 hrs~119 hrs
Furnace Fan500W~18 hrs~24 hrs~30 hrs~36 hrs
LED Lights (10)100W~89 hrs~120 hrs~149 hrs~179 hrs
Sump Pump800W~11 hrs~15 hrs~19 hrs~22 hrs
Essential Bundle*~1 kW~9 hrs~12 hrs~15 hrs~18 hrs

*Essential Bundle = fridge, freezer, furnace fan, 10 LED lights, sump pump, Wi-Fi, and phone charger drawing ~1 kW continuously — a worst-case simultaneous load. 90% usable capacity (≈95% LFP depth × ≈95% conversion). With normal cycling, real-world runtime is typically longer; solar recharges the battery daily.

Choose your EP Cube generation

Two generations. Same Stellar standards.

EP Cube 2.0 is what we install today. Every 1.0 since 2021 stays fully supported.

New · now in stock EP Cube 2.0 home battery: the hybrid inverter and battery stack mounted on an outside wall (manufacturer image)

EP Cube 2.0

Upgraded hybrid inverter (11.5 kW continuous), capacity flexibility from 5 kWh to 40 kWh per single unit, integrated Smart Gateway.

Capacity5–40 kWh / unit (5 kWh modular)
Continuous11.5 kW (15–40 kWh SKUs)
MPPTs6
Motor start (LRA)185 A (15–40 kWh SKUs)
SwitchoverSeamless via Smart Gateway
Warranty10 yr / 6,000 cycles
Consultation pricing

One all-in number, in writing, at your free assessment — we don’t post prices we can’t honour. Size yours in the Designer →

Get my EP Cube 2.0 quote →
Sold out · fully supported

EP Cube 1.0

The proven platform that built our battery track record — hundreds of Stellar installs across Alberta since 2021. Now sold out at the supplier.

Capacity9.9 / 13.3 / 16.6 / 19.9 kWh
Continuous7.6 kW
MPPTs4
Module size3.3 kWh
Switchover<20 ms
Warranty10 years
No longer available

Sold out at the supplier. Every installed 1.0 stays fully supported — and can expand with a paired unit.

Own a 1.0? Get support →

Alberta homes: 5–20 kWh per unit, 40 kWh cap across two units (CEC Rule 64-918); 25–40 kWh single-unit SKUs are commercial. Powerwall 3 vs EP Cube deep-dive →

The Honest Comparison

EP Cube 2.0 vs Tesla Powerwall 3 vs a generator.

We sell the EP Cube. Here’s the comparison anyway — including where the others win.

 EP Cube 2.0Tesla Powerwall 3Whole-home generator
Capacity per unit5–40 kWh, in 5 kWh steps13.5 kWh fixed (27 kWh with two)Unlimited — runs on fuel
Continuous output11.5 kW (15 kWh+ sizes)11.5 kW on-grid; up to 15.4 kW off-grid on an 80 A breaker10–26 kW typical
Motor-start surge185 A LRA185 A LRAEngine-driven
Solar input6 MPPTs built in — no separate inverterIntegrated solar inverterNone
SwitchoverSeamless, automaticSeamless, automatic10–30 s startup blackout
Cold rating-10°C to 50°C (attached-garage install)-20°C to 50°CCold-weather kit needed for -30°C starts
Works with a generator2-wire start generator input built inVia Backup Gateway 2Is the generator
Fuel & maintenanceNoneNoneFuel + ~$200–450/yr servicing

Where Powerwall 3 wins

More off-grid headroom (15.4 kW vs 11.5 kW with proper breaker sizing), a wider -20°C cold rating, an IP67 flood-resistant enclosure, and the strongest brand recognition in the category. If you know you need exactly 13.5 or 27 kWh, it’s the simpler pick.

Where the EP Cube 2.0 wins

Capacity flexibility — start at 5 kWh and grow in 5 kWh steps to Alberta’s 40 kWh cap instead of committing to fixed 13.5 kWh jumps. It matches Powerwall 3 on on-grid output and motor-start surge, has 6 solar MPPTs built in, and is installed here by our own in-house Master Electrician crew.

Where a generator wins

Week-plus outages, if you keep fuel on hand and maintain it. The trade: a 10–30 second blackout at every outage, noise against Edmonton’s 50 dBA nighttime bylaw, and ongoing servicing. Already own one? The EP Cube’s generator input means it’s not either/or. Full 10-year math →

Weighing your battery options? Full Powerwall 3 vs EP Cube 2.0 deep-dive →

Everything included

One price. Every part, every permit, every hour.

Battery garage

  • EP Cube 2.0 battery systemINCLUDED
  • Built-in hybrid inverter, up to 11.5 kWINCLUDED
  • 10-year battery warrantyINCLUDED
  • Lifetime app monitoringINCLUDED
  • Up to 10-year installation warranty5 years on Essentials, 10 on Premium and aboveINCLUDED
  • Generac 18 kW standby generator, installedpad, gas and electrical connections, permitsULTIMATE

Approvals and crew whole job

  • Engineering and system designINCLUDED
  • All permits and utility paperworkINCLUDED
  • Master Electrician installationour own crew, no subcontractorsINCLUDED
  • City inspection and activationINCLUDED
  • App setup and warranty registrationINCLUDED
  • $0-down financing availableon approved creditOPTION

Everything is confirmed at the free site visit. Anything extra is quoted in writing first; approve it, or cancel free.

Zero Surprises

The price you approve is the price you pay — or you don’t pay at all.

Everything is confirmed at the free site visit. Anything extra is quoted in writing first — approve it, or cancel free.

Included in every price

EP Cube 2.0 system · full install by our Master Electrician–led crew · engineering & permits · city inspection · app setup & warranty registration

Confirmed at the site visit

Panel capacity · breaker space · wire run length · floor space for 25–40 kWh dual-tower configs · detached-garage feasibility & temperature

Warranties

Who stands behind what, and for how long.

  • 10
    years · battery

    EP Cube 2.0, or 6,000 cycles, to at least 80% of original capacity.

  • 10
    years · hybrid inverter

    Built into the EP Cube, from Canadian Solar.

  • 5
    years · our workmanship

    10 years on Premium, Elite and Ultimate.

  • 5
    years · generator

    Generac limited warranty. Ultimate.

The same thing as a table: what, who, how long
WhatWhoHow long
EP Cube 2.0 batteryCanadian Solar10 years or 6,000 cycles, to at least 80% of original capacity
Built-in hybrid inverterCanadian Solar10 years
Installation and electrical workStellar Upgrades5 years on Essentials; 10 years on Premium, Elite and Ultimate
Monitoring appCanadian SolarFor the life of the system, at no charge
Generac 18 kW standby generator (Ultimate)Generac5-year limited warranty

Every warranty, in words you don’t need a lawyer to read →

How you’d like to invest

Five ways to pay.

Pay cash and you pay the quoted price. A financed price includes the lender’s finance and transaction fees, and your written offer shows them before you sign.

  • Quoted price
    Pay cash
    50 / 50

    50% deposit on signing, 50% when the system is commissioned and running. The quoted price, with no finance or transaction fees.

  • Lender’s fees included
    In-house financing
    $0 down

    Through our financing partner, on approved credit. The lender pays us. A financed price includes the lender’s finance and transaction fees, shown in your written offer.

  • Paid as cash
    Add it to your mortgage
    Your bank’s rate

    Usually the lowest rate. You pay us as a cash customer does, at the quoted price.

  • Paid as cash
    Home equity line of credit
    Flexible

    Your own line of credit, interest-only if you want it. Quoted price, paid as cash.

  • Rate set by your municipality
    CEIP
    Ask us

    Clean Energy Improvement Program: repaid on your property taxes, where your municipality offers it and the battery is bundled with solar. We confirm it for your address.

Mortgage and line-of-credit customers pay us as cash customers do: 50% on signing, 50% at commissioning. How each option works →

How it happens

From a signature to power on.

Four steps. Done in 4–6 weeks.

  1. Step 1
    Site assessment

    Inspect electrical panel, verify location, confirm final price. Free, no obligation.

  2. Step 2
    Engineering and permits

    We handle all drawings, permits, and utility paperwork.

  3. Step 3
    Installation day

    Mount, wire, connect to panel, configure switchover. About one day.

  4. Step 4
    Inspection and activation

    City inspection, activation, app setup. You’re protected.

Three Stellar Upgrades installers in safety harnesses on a rooftop beside newly mounted solar panels

Who builds it

Our own Red Seal crew. Start to finish.

Stellar’s in-house team of certified electricians and roofers, on payroll, supervised by our Red Seal Master Electrician. We do not subcontract residential installations. Same team from quote to commissioning.

550+Alberta installs
A+BBB rating
5.0Google rating, 40 reviews

No subcontractors on residential installs. Prepaid contracting and direct selling licences from Service Alberta; CEIP qualified contractor.

Recent projects

What a finished install looks like inside.

The part of the job you see every day is the panel. Here is ours on an Edmonton home with solar and an EV charger, photographed after the inspection, beside two of the roofs it belongs to.

Swipe for more →

Siemens panel after solar and EV work: PV disconnect, Tesla load management device, dual-supply labelling, final inspection passed
Siemens panel after solar and EV work: PV disconnect, Tesla load management device, dual-supply labelling, final inspection passedEdmonton, Wedgewood · 11 kW · Premium · September 2026
EPCOR bidirectional meter with dual-power-supply label
EPCOR bidirectional meter with dual-power-supply labelEdmonton, Wedgewood · 11 kW · Premium · September 2026
11 kW Premium rooftop solar install in Edmonton, Alberta, by Stellar Upgrades
Edmonton, Wedgewood · 11 kW · PremiumSeptember 2026
12 kW Premium rooftop solar install in Beaumont, Alberta, by Stellar Upgrades
Beaumont · 12 kW · PremiumOctober 2026

Every install here, with all of its photos, is on the projects page.

Local Installation

Battery backup, installed in your community.

Same crew, same written quote, the right municipal permit — every time. Add to existing solar →  ·  Who’s qualified? →

Save Even More

Pair your battery with solar.

Charges from the sun by day. Runs the house at night. Already have solar? It integrates — and CEIP financing can cover the battery when bundled.

Learn about our solar packages →
Fair questions

Battery backup FAQ.

Asked straight, answered straight. Every question below is one a homeowner has asked us.

Every quote from Stellar Upgrades is all-in: the battery system, built-in hybrid inverter, all electrical work by our master electricians, engineering, permitting, and city inspection are included — no hidden fees, and $0-down financing is available. We install the EP Cube 2.0 (5–40 kWh, now in stock); your free assessment includes the confirmed all-in number in writing before you sign. As a rule of thumb, the battery, inverter, and gateway hardware is roughly 60% of a full Alberta installation — design, engineering, permits, electrical materials, licensed labour, commissioning, inspection, and warranty backing make up the other 40%, and your written quote itemizes it. (The original EP Cube 1.0 and its posted pricing are sold out.) Size your system in the Backup Designer, then we'll give you the exact number for your home. Financing details →

Runtime depends on battery size and power usage. At 90% usable capacity with essential loads (fridge, furnace fan, lights, sump pump, Wi-Fi) drawing ~1 kW continuously — a conservative worst case — the EP Cube 2.0 runs ~4.5 hours (5 kWh), ~9 hours (10 kWh), ~13 hours (15 kWh), or ~18 hours (20 kWh). Real appliances cycle on and off, so with realistic winter duty cycles the same essentials average ~530 W and runtimes roughly double — model your own loads in the Backup Designer. Running only a fridge and freezer, a 10 kWh unit lasts ~60 hours (about 2½ days). Paired with solar, the battery recharges daily and can ride through multi-day outages.

A battery switches over automatically in milliseconds — you won't notice the outage. A generator requires manual startup in the dark, produces noise and carbon monoxide, needs ongoing fuel and maintenance, and is restricted or banned in many residential areas. The EP Cube is silent, zero-maintenance, zero-fuel, and operates automatically. It also has no carbon monoxide risk, making it safe for indoor installation.

Yes. The EP Cube is compatible with existing solar installations and third-party inverters. Its built-in hybrid inverter supports both AC and DC coupling, meaning it can integrate with virtually any existing solar setup. If you don't have solar, the battery still works — it charges from the grid and provides backup during outages. Learn about adding solar →

The EP Cube battery carries a 10-year manufacturer warranty from Canadian Solar. The built-in hybrid inverter also has a 10-year warranty. Stellar Upgrades adds a 5-year installation warranty (10-year on the Premium package) covering all electrical work and installation. The EP Cube app for monitoring is included for the lifetime of the system at no additional cost.

Yes. The EP Cube 2.0 is modular in 5 kWh steps, so capacity can be added to the same unit as your needs grow. Up to two EP Cube units can be paralleled in an Alberta home, capped at the 40 kWh aggregate residential limit set by Canadian Electrical Code Rule 64-918. This makes it suitable for any home size, from essential-circuit backup to whole-home independence — and existing EP Cube 1.0 owners can expand with a paired unit too.

The EP Cube is wall-mounted, typically in your attached garage, which stays within the unit’s -10°C to 50°C operating range even when it’s -40°C outside. It has a NEMA 4X rating (waterproof and dustproof). An unheated detached garage can drop below the minimum operating temperature in an Edmonton winter, so detached installs are assessed case-by-case at your free site visit. It installs in an attached garage, a detached garage, or inside the home — typically the basement — in a dedicated battery utility room — 18-inch clearance on both sides, a fire-rated door, a fire alarm, and an exhaust fan, built and permitted as part of the job. Our Master Electrician handles all mounting, wiring, panel integration, and permitting.

EP Cube 2.0 upgrades the hybrid inverter from 7.6 kW continuous to 11.5 kW continuous (15–40 kWh SKUs) and adds 185 A LRA motor-start surge. Capacity moves from a fixed 9.9/13.3/16.6/19.9 kWh lineup to 5 kWh modular increments from 5 to 40 kWh per single unit. MPPTs increase from 4 to 6, EV charger compatibility expands to 2 × 40 A Level 2 chargers, and the Smart Gateway is upgraded with seamless on-grid / off-grid switchover. Both share the same LFP chemistry and 10-year / 6,000-cycle warranty backed by Canadian Solar. EP Cube 1.0 is now sold out at the supplier; EP Cube 2.0 is the generation we install today, with your confirmed all-in price provided in writing at the free assessment. Every 1.0 system we’ve installed remains fully supported. Full EP Cube 2.0 spec deep-dive →

The EP Cube warranty guarantees at least 80% of original capacity at 10 years or 6,000 cycles, whichever comes first — many competing batteries only warrant 70%. LFP chemistry degrades slowly, so the system doesn’t stop at year 10; it keeps operating at reduced capacity, and LFP home batteries commonly remain useful well beyond the warranty period. Because the EP Cube is modular, capacity can also be added later if your needs grow.

There is currently no provincial rebate for a standalone home battery in Alberta — we’d rather tell you that straight than imply savings that don’t exist. Municipal CEIP financing (Edmonton, St. Albert, Spruce Grove, Beaumont and others) can fund a battery when it’s bundled with a solar installation, and $0-down term financing is available on approved credit. Financing details →

Yes. It’s not either/or — the EP Cube 2.0 has a generator input, and we have integrated EP Cube systems with existing standby generators on 1.0 installs as well. The battery handles the instant, silent switchover and daily backup; the generator becomes the deep reserve for extended outages. Our Sherwood Park customer story above is exactly this setup: solar by day, battery at night, Generac as final backup, fully automatic.

Yes — Stellar Upgrades is BBB A+ accredited. Our profile is publicly maintained by the Better Business Bureau at bbb.org. We’re also fully insured ($5M general liability), WCB clearance current, and operating since 2018 with the same Red Seal Master Electrician on every electrical permit. More on the company →

Yes. We pay a flat $500 per battery backup install on commissioning to anyone who refers a homeowner who installs with Stellar — plus $100 per installed kilowatt on solar referrals and $100 per EV charger. You can take it as cash, apply it as credit on your own next upgrade, or pass it forward as a discount to the new customer.

Stellar’s in-house team of certified electricians and roofers, on payroll, supervised by our Red Seal Master Electrician. We do not subcontract residential installations. Same team from quote to commissioning — whether you meet us at your door, on the phone, by email, or through a referral. 11 questions every Alberta homeowner should ask →
$100per kW installed

Refer a neighbour. Get paid. Or pass it forward.

Refer a homeowner who installs with Stellar: $500 per battery, $100 per solar kW, $100 per EV charger — as cash, credit, or a gift to them.

Example: refer a 12 kW solar + battery install → $1,200 paid on commissioning
Book

The next outage isn’t a question of if.
It’s when.

Free assessment. Exact written price. No obligation. We check your electrical panel and where the battery would live, then put an all-in price in writing. If backup isn’t right for your home, we’ll tell you.

Prefer to talk now? Call (780) 200-5265, Monday to Friday 10 am to 8 pm, Saturday 10 am to 6 pm.

Book a free assessment.

We’ll call or text within 24 hours to set a time.

What are you interested in?

By submitting, you consent to Stellar Upgrades contacting you by phone, text or email about your inquiry. Unsubscribe anytime. Privacy Policy

PJ Singh, Founder & Owner of Stellar Upgrades
Free consult · Google Meet · 30 minutes

Talk it through with an energy expert.

A free 30-minute Google Meet with one of our energy experts — your bill, your roof, your actual numbers. If it’s not the right fit for your home, we’ll tell you that too. No pressure, no chasing.

Book a free video consult →
5.0★ Google · 40 reviews · BBB A+ accredited · Red Seal Master Electrician‑led

Stellar Upgrades at a glanceStellar Upgrades is a trade name of Right Wire Technologies Ltd., an electrical contractor at Unit 10, 6005 103A St NW, Edmonton, AB T6H 2J7 · (780) 200-5265 · info@stellarupgrades.ca. It installs residential solar panels, EP Cube battery backup, Level 2 EV chargers and permanent exterior lighting across the Edmonton region, central Alberta and the Calgary region. Installs are done by in-house electricians under a Master Electrician. Licences: Service Alberta prepaid contracting and direct selling (numbers available on request). CEIP qualified contractor and direct EP Cube dealer. Operating since 2018. Google rating 5.0 from 40 reviews. Hours: Monday to Friday 10 AM to 8 PM, Saturday 10 AM to 6 PM. Service areas.

Call (780) 200-5265Book a free assessment